怎么安裝玻璃門前拉手？

How to install glass door handle？

1、全玻璃門扇上玻璃門拉手孔洞，一般在裁割玻璃時加工完成。玻璃門拉手連接部分插洞口時不能過緊，應略有松動；如插入過松，可在插入部分裹上軟質膠帶。  

1、Glass door handle holes, generally in cutting glass processing to complete. Glass door handle connecting portion in the hole cannot be too tight should be slightly loose; such as inserting too loose, can be inserted in the partially wrapped soft tape.

2、安裝前在玻璃門拉手插入玻璃的部分涂少許玻璃膠。拉手組裝時，其根部與玻璃靠緊密后再按緊固定螺釘，以保證拉手沒有松動現象。

2、Before install the glass door handle , we can spread on some glass cement in the glass door hole. When the handle is assembled, the root of the handle is tightly pressed by the glass, and then presses the fastening screw to ensure that the handle is not loose.

 3、如果玻璃門不是鋼化玻璃的話，用10mm的玻璃鉆頭，量出玻璃門拉手的孔距（中心到中心），在玻璃門上標記好，澆水打孔，安裝時先從外面上，在里面擰好拉手的長螺絲，別把拉手的螺絲留外面了，那樣能夠從外面把玻璃門拉手卸掉的。

3、If the glass door not toughened glass，measure the glass door handle hole spacing（from center to center），marking，watering and using 10mm glass bit dig the hole in the glass door. Firstly installation outside，tighten the screws inside，do not let the screws to stay outside the surface that cause the handle can be removing from outside.

4、選擇的玻璃門拉手必須要和玻璃門匹配，這樣拉手才會和牢固，與玻璃門搭配也才會更美觀。

4、Finally is the most important，, the choice of glass door handle must be matched with the glass door, so that the handle will be firmly, and the glass door will be more beautiful with glass door handle.

拉手日常維護方法

1、請于裝修完工并清潔現場后，才裝拉手。防止施工過程中或清理現場時有磕傷碰花或清潔員工用含堿性清潔劑清潔拉手

2、每周至少清潔一次拉手表面

3、清潔拉手表面時請用柔軟的干布抹擦，表面汗油或灰塵嚴重時，可用干布沾上滑石粉用力擦拭表面，即可光亮如新

4、千萬不能用酸堿（含有腐蝕性）清潔劑清潔拉手，這樣容易腐蝕金屬表面引起氧化生銹